Hi guys...Just wondering if there is any rule/regulation as to how close a gas bayonet fitting can be from the gas bottles on the front of a caravan? A friend told my mate that there is a distance...any idea folks...Also have a safe Christmas and happy new year...Be safe
Lance
blissonwheels said
07:08 PM Dec 23, 2016
Gooday,
v Make sure you have a sufficient size copper pipe or whatever you use, I had one fitted to rear of 21 ft caravan they only used 6 mm bore tube, not large enough will not run our WeberQ100 on it, not enough gas.
Cheers,
patrol03 said
08:09 PM Dec 23, 2016
As suggested CD,The distance would depend on what you are trying to run. At home we use gas for heating and I have a 3m flexible pipe from the wall in the family room. The point is fed in 1/2" copper from the gas bottle.and I run a large Brigadier gas heater. You could always replumb your van gas system to a more appropriate takeoff point.To answer your original question about a regulation distance I really don't think there is one. e.g. Our bottles are up the front and the kitchen is at the rear of the van.Someone who is better versed than I on this subject may beg to differ.
Peter_n_Margaret said
09:14 PM Dec 23, 2016
I suggest the gas bayonet should be at least 1.5m from the gas bottles, PLUS the maximum length of a hose assembly, because the appliance is an ignition source and should not be closer than 1.5m from the bottles.
Thanx for putting that up..I have read the guff but cannot see where it says the bayonet should be 1.5m from the bottles..Could you please explain for this old guy... :)
Lance
Peter_n_Margaret said
10:36 PM Dec 23, 2016
It does not talk about a bayonet Lance, but it does say the gas bottles should not be closer than 1.5m from a source of ignition and what you run from the bayonet is a source of ignition, so it should not be possible (as I read it) for that BBQ (or whatever) to ever be closer than 1.5m from the gas bottles when it is connected and running.
Cheers,
Peter
Crazy Dog said
10:42 PM Dec 23, 2016
I have a 3m hose that connects from the bayonet to a Ziggy instead of connection to the pol fitting on the gas bottle..
Hylife said
01:47 PM Dec 24, 2016
"Should" and "must not be" are two very different things.
That document linked by Peter_n_Margaret is very old and mostly out of date. The Australian Standards (AS) regarding gas have been changed 2 or 3 times since it was written.
New laws are not retrospective. EG, a van may have had gas work done legally some years ago and a certificate issued, but just because the laws have now changed does NOT make your installation illegal. If however you have any modification work done then you are required to bring the entire system up to spec with the new laws and to have it re-certified.
Gas laws vary widely from state to state and whilst some states reference the AS for certain portions of their rules, it is often a mix of AS and local rules that make up their laws. I suggest you approach a licenced Gas Fitter in the state that your van is registered in and have them perform the work and issue a compliance certificate.
Peter_n_Margaret said
04:57 PM Dec 24, 2016
That document linked by Peter_n_Margaret is very old and mostly out of date. The Australian Standards (AS) regarding gas have been changed 2 or 3 times since it was written.
Maybe you could post something more current to answer the OP's question if that is the case?
Or maybe you actually don't have a clue?
Cheers,
Peter
Spook said
08:41 PM Dec 24, 2016
Peter_n_Margaret wrote:
That document linked by Peter_n_Margaret is very old and mostly out of date. The Australian Standards (AS) regarding gas have been changed 2 or 3 times since it was written.
Maybe you could post something more current to answer the OP's question if that is the case?
Or maybe you actually don't have a clue?
Cheers,
Peter
That document is obsolete, Peter. I have the complete document but I am not at liberty to attach the lot. If you want a section on a particular regulation/standard I can search for same. You are however correct with the requirement to maintain a distance of 1.5 metres between gas cylinder and source of ignition.
-- Edited by Spook on Saturday 24th of December 2016 08:44:30 PM
Peter_n_Margaret said
09:11 PM Dec 24, 2016
Spook wrote:
You are however correct with the requirement to maintain a distance of 1.5 metres between gas cylinder and source of ignition.
Which was the bit relevant to the OPs question. Thank you for that confirmation!
Cheers,
Peter
Crazy Dog said
09:51 PM Dec 24, 2016
So I can put the bayonet right next to a gas bottle as long as the bbq is at least 1.5m away from the bayonet or bottle
Joe50 said
12:44 AM Dec 25, 2016
My Hino Rainbow has the gas bottle in a compartment at the rear left-hand corner of the vehicle, and I have a bayonet located one metre in front of the centre of the compartment. I was told prior to the fit-out (in Brisbane, end of 2014) that the bayonet could not be located below a wind-out awning, to comply with new regulations that came into effect from July 2014. I presume this is because annex walls could be erected around the awning and the bayonet would then be within a 'livable area'.
As this work must be done and certified by a licensed gasfitter, I suggest that you follow Hylife's advice.
Joe
oldtrack123 said
07:23 PM Jan 1, 2017
Joe50 wrote:
.
As this work must be done and certified by a licensed gasfitter, I suggest that you follow Hylife's advice.
Joe
DITTO
Liam McGlinn said
12:52 AM Mar 28, 2017
Recently, I have hired the services of "The Plumbing and Gas Guys", for gas installation, as they are the experts and undertake all types of gas installations and are licensed gas fitters, domestic plumbers and commercial plumbers.
-- Edited by Liam McGlinn on Tuesday 28th of March 2017 12:53:03 AM
Hi guys...Just wondering if there is any rule/regulation as to how close a gas bayonet fitting can be from the gas bottles on the front of a caravan? A friend told my mate that there is a distance...any idea folks...Also have a safe Christmas and happy new year...Be safe
Lance
Gooday,
v Make sure you have a sufficient size copper pipe or whatever you use, I had one fitted to rear of 21 ft caravan they only used 6 mm bore tube, not large enough will not run our WeberQ100 on it, not enough gas.
Cheers,
I suggest the gas bayonet should be at least 1.5m from the gas bottles, PLUS the maximum length of a hose assembly, because the appliance is an ignition source and should not be closer than 1.5m from the bottles.
Cheers,
Peter
hI Peter,
Thanx for putting that up..I have read the guff but cannot see where it says the bayonet should be 1.5m from the bottles..Could you please explain for this old guy... :)
Lance
Cheers,
Peter
I have a 3m hose that connects from the bayonet to a Ziggy instead of connection to the pol fitting on the gas bottle..
"Should" and "must not be" are two very different things.
That document linked by Peter_n_Margaret is very old and mostly out of date. The Australian Standards (AS) regarding gas have been changed 2 or 3 times since it was written.
New laws are not retrospective.
EG, a van may have had gas work done legally some years ago and a certificate issued, but just because the laws have now changed does NOT make your installation illegal.
If however you have any modification work done then you are required to bring the entire system up to spec with the new laws and to have it re-certified.
Gas laws vary widely from state to state and whilst some states reference the AS for certain portions of their rules, it is often a mix of AS and local rules that make up their laws.
I suggest you approach a licenced Gas Fitter in the state that your van is registered in and have them perform the work and issue a compliance certificate.
Maybe you could post something more current to answer the OP's question if that is the case?
Or maybe you actually don't have a clue?
Cheers,
Peter
That document is obsolete, Peter. I have the complete document but I am not at liberty to attach the lot. If you want a section on a particular regulation/standard I can search for same. You are however correct with the requirement to maintain a distance of 1.5 metres between gas cylinder and source of ignition.
-- Edited by Spook on Saturday 24th of December 2016 08:44:30 PM
Which was the bit relevant to the OPs question. Thank you for that confirmation!
Cheers,
Peter
As this work must be done and certified by a licensed gasfitter, I suggest that you follow Hylife's advice.
Joe
DITTO
Recently, I have hired the services of "The Plumbing and Gas Guys", for gas installation, as they are the experts and undertake all types of gas installations and are licensed gas fitters, domestic plumbers and commercial plumbers.
-- Edited by Liam McGlinn on Tuesday 28th of March 2017 12:53:03 AM