check out the new remote control Jockey Wheel SmartBar rearview170 Beam Communications SatPhone Shop Topargee products Enginesaver Low Water Alarms
Members Login
Username 
 
Password 
    Remember Me  
Post Info TOPIC: Voltech error code


Guru

Status: Offline
Posts: 5525
Date:
Voltech error code


Hi, I really need help, our Voltech ISC3040 has a E5 code on the dial, operating book goes to E4.

The 2x170 watts solar panels linked with 2x100 amp batteries has been working great since October 2016 but yesterday when I was up the caravan to my horror this message was on the screen.

The batteries are holding 12.6 volts but was earlier in the day, solar was pumping in 13.4 volts.

Can any one for warn me what the problem may be please.



-- Edited by Radar on Tuesday 7th of May 2019 06:52:14 AM

__________________


Veteran Member

Status: Offline
Posts: 28
Date:

Radar, Maybe some help in this link, www.exploroz.com/forum/103640/error-code-on-solar-regulator

Good luck, B.

__________________


Guru

Status: Offline
Posts: 5525
Date:

Thank you Kiwoz.

All sorted, I rang the Voltech service, Mark was excellent in helping me sort the problem with the E5 error code.

Needed a set manual reset by removing the 2 earth wires from the mppt and counting to 20, replace and all is good.

Voltech is a Brisbane based company eager help with customer service.



__________________


Newbie

Status: Offline
Posts: 1
Date:

I have the same issue with my controller. But, when I removed the earth on the solar side and the controller came on. When I replaced that wire, everything cut out again.
Anybody experienced the same ?
Thanks in advance.

__________________


Guru

Status: Offline
Posts: 4185
Date:

Almacbokke wrote:

I have the same issue with my controller. But, when I removed the earth on the solar side and the controller came on. When I replaced that wire, everything cut out again.


I would star by measuring the voltages at the battery terminals, solar panel, and the inputs and outputs of the MPPT controller.

See what changes when you cover the panels with a blanket.

Connect the battery to a large load and see if that changes anything.



__________________

"No friend ever served me, and no enemy ever wronged me, whom I have not repaid in full."

Lucius Cornelius Sulla - died 78 BC 

 



Guru

Status: Offline
Posts: 561
Date:

Start at the beginning.  Disconnect the solar from the solar panels and the battery.  Check your battery voltage as Dorian has stated. Wait a couple of minutes then connect your controller to the battery first.  Let the controller determine the battery voltage for a minute then reconnect to your solar panels.

What make and model is your solar controller.

Most solar controllers require connection to the battery first and to solar panels second.

If it cuts out again when connecting the solar panels measure the panels voltage.

 

Tim 



-- Edited by TimTim on Saturday 20th of April 2024 01:39:38 PM

__________________


Guru

Status: Offline
Posts: 1330
Date:

Almacbokke wrote:

I have the same issue with my controller. But, when I removed the earth on the solar side and the controller came on. When I replaced that wire, everything cut out again.
Anybody experienced the same ?
Thanks in advance.


 Hey Alan, Welcome,

Start a new post outlining the problem that you are experiencing and provide details of the equipment.

You will get more responses that way.



__________________

Cheers, Richard (Dick0)

"Home is where the Den is parked, Designer Orchid Special towed by Jeep Grand Cherokee Limited"

"4x250W solar panels, Epever 80A charger and 3x135Ah Voltax Prismatic LiFePO4 Batteries".

Page 1 of 1  sorted by
 
Quick Reply

Please log in to post quick replies.

Tweet this page Post to Digg Post to Del.icio.us
Purchase Grey Nomad bumper stickers Read our daily column, the Nomad News The Grey Nomad's Guidebook